1. Forum
  2. FidoNet
  3. Mystic Support

  • Latest prealpha build

    From Robert Wolfe@1:116/18 to All on Monday, November 30, 2020 18:03:59
    Hi all!

    Downloaded and installed the latest prealpha build on my CentOS 8.x-
    based laptop. It runs fine, however there are two issues I am seeing:

    1. QWKPOLL does not poll when I tell it to. It just displays the program information line and then returns to the command prompt. I actually have
    to use the ftp command line client to transfer the QWK packet nad
    then run qwkpoll in import mode to import the packets. The same thing in reverse when I have outgoing mail.

    2. When I go to reply to a message when logged in, I hit ENTER to access
    the defaults, but then I just get returned to the message menu without ever getting tossed into the editor like I am supposed to.

    So, am I doing something wrong here? I have not "upgraded: my Windows
    Mystic system yet for this very reason.

    ... Heisenberg may have slept here.
    ___ MultiMail/Linux v0.52

    --- Mystic BBS/QWK v1.12 A47 2020/09/07 (Windows/64)
    * Origin: Omicron Theta * Southaven MS * winserver.org:2300 (1:116/18)
  • From g00r00@1:129/215 to Robert Wolfe on Monday, November 30, 2020 21:16:37
    1. QWKPOLL does not poll when I tell it to. It just displays the program information line and then returns to the command prompt. I actually have

    Have you configured a QWK network, is it set to active, and is it set to "Member Type: Node"? Is the archive type and packet ID set to something?

    2. When I go to reply to a message when logged in, I hit ENTER to access the defaults, but then I just get returned to the message menu without evergetting tossed into the editor like I am supposed to.

    Did you perform a fresh install or is this an upgrade? If its an upgrade and you haven't upgraded in a while there are probably things you need to do to make it work. Do the logs say anything?

    And since its Linux do you understand how access and ownership works in Linux file systems? It could be something along those lines too.

    --- Mystic BBS v1.12 A47 2020/11/23 (Windows/64)
    * Origin: Sector 7 | Mystic WHQ (1:129/215)
  • From Robert Wolfe@1:116/18 to g00r00 on Saturday, January 09, 2021 17:56:34
    On 30 Nov 2020, g00r00 said the following...

    Have you configured a QWK network, is it set to active, and is it set to "Member Type: Node"? Is the archive type and packet ID set to something?

    Actually have it set to member type "hub" IIRC.

    Did you perform a fresh install or is this an upgrade? If its an
    upgrade and you haven't upgraded in a while there are probably things
    you need to do to make it work. Do the logs say anything?

    This is a a fresh installation.

    And since its Linux do you understand how access and ownership works in Linux file systems? It could be something along those lines too.

    Of course. I would not have earned my Linux certification or be a senior
    Linux engineer where I work if I didn't understand how access and ownership works :)

    --- Mystic BBS v1.12 A47 2020/09/07 (Windows/64)
    * Origin: Omicron Theta * Memphis, TN * winserver.org:2300 (1:116/18)
  • From g00r00@1:129/215 to Robert Wolfe on Monday, January 11, 2021 13:11:42
    Have you configured a QWK network, is it set to active, and is it set "Member Type: Node"? Is the archive type and packet ID set to someth

    Actually have it set to member type "hub" IIRC.

    The "Member Type" should be set to "Node", give that a shot.

    When you're set to run in as a Hub QWKPOLL will not try to connect to anything because you are the Hub (ie nodes connect to you to send/receive messages).

    --- Mystic BBS v1.12 A47 2021/01/05 (Windows/64)
    * Origin: Sector 7 | Mystic WHQ (1:129/215)